B. Tech (VSSUT Burla)
M. Tech (NIT Trichy)

Thermal Engineering

PMEC – Since 20.10.2024

• ICGT, ETD, AFM, TD, NCE
• Non-conventional energy
• Computational fluid dynamics
• Heat transfer
• Applied thermodynamics,
• Internal combustion engine
• Green energy
• Advanced fluid mechanics

“Awarded appreciation by the Department of Science and Technology (DST) and
the Texas Instruments India Innovation Challenge Design Contest 2018 for fostering an ecosystem
that effectively bridges industry and academia.”

[1] S. Samantaray, “Computational Analysis of Single-Phase Heat Transfer and Friction Factor in Micro Fin Tubes,” Regd. No. 1607109028.

[2] S. K. Panda, “A Numerical Study of Heat Transfer Analysis of Premixed CNG/Air Laminar Flame Impinging on a Flat Surface,” Registration No. 1707109027.

[3] M. R. Patro, “Effects of Various Parameters on Performance of Y-Shaped Hexagonal Diffusing Duct,” Regd. No. 1707109004.

[4] R. R. Parida, “Computational Flow Analysis of Asymmetric NACA Airfoil Blade,” Regd. No. 1707109033.

[5] R. R. Apatta, “Two-Dimensional Analysis of Tandem Compressor Blades,” Regd. No. 1707109009.

[6] S. Patra, “Analysis of Wear and Mechanical Properties of High-Density Polyethylene–Cu–SiC Hybrid Composite,” Regd. No. 2007109002.

• Faculty coordinator start-up innovation club (2021-23),Member in Purchase committee.
• Member in College Magazine (DARABAR).

[1] K. Dhamudia and J. R. Senapati, “A computational study to optimize the configuration of diamond-shaped rib turbulators for assessing the thermo-hydraulic performance parameter,” International Journal of Thermal Sciences, vol. 223, p. 110618, 2026.

[2] S. Chanda, K. Dhamudia, and J. R. Senapati, “A computational study of rivet ribs in solar air heater ducts,” in Advancing Sustainable Engineering Through Next-Generation Thermo-Fluid …, 2026.

[3] K. Dhamudia and J. R. Senapati, “A numerical study of thermo-fluid performance characteristics in an air duct with hook-shaped turbulence promoters on a heated plate,” International Communications in Heat and Mass Transfer, vol. 169, p. 109538, 2025.

[4] S. Chanda, K. Dhamudia, and J. R. Senapati, “Heat transfer enhancement using rivet-type rib turbulators in a rectangular channel: A CFD study,” Thermal Science and Engineering Progress, p. 104019, 2025.

[5] K. Dhamudia and J. R. Senapati, “A computational study for enhancement in thermal performance of plus (+)-shaped ribbed solar air heater duct,” International Communications in Heat and Mass Transfer, vol. 161, p. 108411, 2025.

[6] R. Choudhary, K. Dhamudia, and J. R. Senapati, “CFD investigation of pin-finned cooling techniques for solar PV modules,” 2025.

[7] K. Dhamudia, R. Choudhary, and J. R. Senapati, “A thermal performance evaluation of photovoltaic cell using inverted T-shaped fins,” 2025.

[8] K. Dhamudia, S. K. Mahato, R. K. Singh, A. Kumar, S. K. Panda, M. K. Sahu, et al., “Heat propagation phenomenon of compressed natural gas/air premixed laminar flame impinging on a flat surface,” Case Studies in Thermal Engineering, vol. 64, p. 105571, 2024.

[9] K. Dhamudia and J. R. Senapati, “A comparative analysis of rhombus shaped ribs in solar air heater,” 2023.

[10] K. Dhamudia and P. K. Mishra, “Numerical investigation for improved heat transfer characteristics in micro-fin tubes,” Heat Transfer, vol. 50, no. 1, pp. 688–711, 2021.

• 02 Seminars
• 03 conferences
• 10 FDP
• 05 STC

Department of Mechanical Engineering,

Parala Maharja Engineering College, Sitalapalli, Berhampur – 761003.